ajout des fichiers de configuration du service DHCP et la config des cartes réseau du serveur

sisr1/tp01-nat-dhcp/cartes_reseau/interfaces

@@ -0,0 +1,24 @@
+# This file describes the network interfaces available on your system
+# and how to activate them. For more information, see interfaces(5).
+
+source /etc/network/interfaces.d/*
+
+# The loopback network interface
+auto lo
+iface lo inet loopback
+
+# The primary network interface
+allow-hotplug enp0s3
+iface enp0s3 inet dhcp
+
+# Assignation static IP adresse
+# auto enp0s3
+# iface enp0s3 inet static
+#	address 192.168.0.26/24
+#	gateway 192.168.0.1
+
+# Assignation static IP adresse
+auto enp0s8
+iface enp0s8 inet static
+	address 192.168.2.1/24
+#	gateway 192.168.0.1

sisr1/tp01-nat-dhcp/srv-dhcp/dhcpd.conf

@@ -0,0 +1,107 @@
+# dhcpd.conf
+#
+# Sample configuration file for ISC dhcpd
+#
+
+# option definitions common to all supported networks...
+option domain-name "example.org";
+option domain-name-servers ns1.example.org, ns2.example.org;
+
+default-lease-time 3600;
+max-lease-time 604800;
+
+# The ddns-updates-style parameter controls whether or not the server will
+# attempt to do a DNS update when a lease is confirmed. We default to the
+# behavior of the version 2 packages ('none', since DHCP v2 didn't
+# have support for DDNS.)
+ddns-update-style none;
+
+# If this DHCP server is the official DHCP server for the local
+# network, the authoritative directive should be uncommented.
+#authoritative;
+
+# Use this to send dhcp log messages to a different log file (you also
+# have to hack syslog.conf to complete the redirection).
+#log-facility local7;
+
+# No service will be given on this subnet, but declaring it helps the 
+# DHCP server to understand the network topology.
+
+#subnet 10.152.187.0 netmask 255.255.255.0 {
+#}
+
+# This is a very basic subnet declaration.
+
+subnet 192.168.2.0 netmask 255.255.255.0 {
+	range 192.168.2.10 192.168.2.100;
+	option routers 192.168.2.1;
+	option domain-name-servers 10.121.38.7;
+#  option routers rtr-239-0-1.example.org, rtr-239-0-2.example.org;
+}
+# This declaration allows BOOTP clients to get dynamic addresses,
+# which we don't really recommend.
+
+#subnet 10.254.239.32 netmask 255.255.255.224 {
+#  range dynamic-bootp 10.254.239.40 10.254.239.60;
+#  option broadcast-address 10.254.239.31;
+#  option routers rtr-239-32-1.example.org;
+#}
+
+# A slightly different configuration for an internal subnet.
+#subnet 10.5.5.0 netmask 255.255.255.224 {
+#  range 10.5.5.26 10.5.5.30;
+#  option domain-name-servers ns1.internal.example.org;
+#  option domain-name "internal.example.org";
+#  option routers 10.5.5.1;
+#  option broadcast-address 10.5.5.31;
+#  default-lease-time 600;
+#  max-lease-time 7200;
+#}
+
+# Hosts which require special configuration options can be listed in# host statements.   If no address is specified, the address will be
+# allocated dynamically (if possible), but the host-specific information
+# will still come from the host declaration.
+
+#host passacaglia {
+#  hardware ethernet 0:0:c0:5d:bd:95;
+#  filename "vmunix.passacaglia";
+#  server-name "toccata.example.com";
+#}
+
+# Fixed IP addresses can also be specified for hosts.   These addresses
+# should not also be listed as being available for dynamic assignment.
+# Hosts for which fixed IP addresses have been specified can boot using
+# BOOTP or DHCP.   Hosts for which no fixed address is specified can only
+# be booted with DHCP, unless there is an address range on the subnet
+# to which a BOOTP client is connected which has the dynamic-bootp flag
+# set.
+host fantasia {
+  hardware ethernet 08:00:27:77:70:0d;
+  fixed-address 192.168.2.102;
+}
+
+# You can declare a class of clients and then do address allocation
+# based on that.   The example below shows a case where all clients
+# in a certain class get addresses on the 10.17.224/24 subnet, and all
+# other clients get addresses on the 10.0.29/24 subnet.
+
+#class "foo" {
+#  match if substring (option vendor-class-identifier, 0, 4) = "SUNW";
+#}
+
+#shared-network 224-29 {
+#  subnet 10.17.224.0 netmask 255.255.255.0 {
+#    option routers rtr-224.example.org;
+#  }
+#  subnet 10.0.29.0 netmask 255.255.255.0 {
+#    option routers rtr-29.example.org;
+#  }
+#  pool {
+#    allow members of "foo";
+#    range 10.17.224.10 10.17.224.250;
+#  }
+#  pool {
+#    deny members of "foo";
+#    range 10.0.29.10 10.0.29.230;
+#  }
+#}

sisr1/tp01-nat-dhcp/srv-dhcp/isc-dhcp-server

@@ -0,0 +1,18 @@
+# Defaults for isc-dhcp-server (sourced by /etc/init.d/isc-dhcp-server)
+
+# Path to dhcpd's config file (default: /etc/dhcp/dhcpd.conf).
+#DHCPDv4_CONF=/etc/dhcp/dhcpd.conf
+#DHCPDv6_CONF=/etc/dhcp/dhcpd6.conf
+
+# Path to dhcpd's PID file (default: /var/run/dhcpd.pid).
+#DHCPDv4_PID=/var/run/dhcpd.pid
+#DHCPDv6_PID=/var/run/dhcpd6.pid
+
+# Additional options to start dhcpd with.
+#	Don't use options -cf or -pf here; use DHCPD_CONF/ DHCPD_PID instead
+#OPTIONS=""
+
+# On what interfaces should the DHCP server (dhcpd) serve DHCP requests?
+#	Separate multiple interfaces with spaces, e.g. "eth0 eth1".
+INTERFACESv4="enp0s8"
+INTERFACESv6=""