Premier commit

roles/snmp-cs/files/snmpd.conf

@@ -0,0 +1,193 @@
+###############################################################################
+#
+# EXAMPLE.conf:
+#   An example configuration file for configuring the Net-SNMP agent ('snmpd')
+#   See the 'snmpd.conf(5)' man page for details
+#
+#  Some entries are deliberately commented out, and will need to be explicitly activated
+#
+###############################################################################
+#
+#  AGENT BEHAVIOUR
+#
+
+#  Listen for connections from the local system only
+#agentAddress  udp:127.0.0.1:161
+#  Listen for connections on all interfaces (both IPv4 *and* IPv6)
+agentAddress udp:161,udp6:[::1]:161
+
+
+
+###############################################################################
+#
+#  SNMPv3 AUTHENTICATION
+#
+#  Note that these particular settings don't actually belong here.
+#  They should be copied to the file /var/lib/snmp/snmpd.conf
+#     and the passwords changed, before being uncommented in that file *only*.
+#  Then restart the agent
+
+#  createUser authOnlyUser  MD5 "remember to change this password"
+#  createUser authPrivUser  SHA "remember to change this one too"  DES
+#  createUser internalUser  MD5 "this is only ever used internally, but still change the password"
+
+#  If you also change the usernames (which might be sensible),
+#  then remember to update the other occurances in this example config file to match.
+
+
+
+###############################################################################
+#
+#  ACCESS CONTROL
+#
+
+                                                 #  system + hrSystem groups only
+view   systemonly  included   .1.3.6.1.2.1.1
+view   systemonly  included   .1.3.6.1.2.1.25.1
+
+                                                 #  Full access from the local host
+rocommunity public  s-mon.gsb.adm
+                                                 #  Default access to basic system info
+rocommunity public  
+
+                                                 #  Full access from an example network
+                                                 #     Adjust this network address to match your local
+                                                 #     settings, change the community string,
+                                                 #     and check the 'agentAddress' setting above
+#rocommunity secret  10.0.0.0/16
+
+                                                 #  Full read-only access for SNMPv3
+ rouser   authOnlyUser
+                                                 #  Full write access for encrypted requests
+                                                 #     Remember to activate the 'createUser' lines above
+#rwuser   authPrivUser   priv
+
+#  It's no longer typically necessary to use the full 'com2sec/group/access' configuration
+#  r[ou]user and r[ow]community, together with suitable views, should cover most requirements
+
+
+
+###############################################################################
+#
+#  SYSTEM INFORMATION
+#
+
+#  Note that setting these values here, results in the corresponding MIB objects being 'read-only'
+#  See snmpd.conf(5) for more details
+sysLocation    Sitting on the Dock of the Bay
+sysContact     Me <me@example.org>
+                                                 # Application + End-to-End layers
+sysServices    72
+
+
+#
+#  Process Monitoring
+#
+                               # At least one  'mountd' process
+proc  mountd
+                               # No more than 4 'ntalkd' processes - 0 is OK
+proc  ntalkd    4
+                               # At least one 'sendmail' process, but no more than 10
+proc  sendmail 10 1
+
+#  Walk the UCD-SNMP-MIB::prTable to see the resulting output
+#  Note that this table will be empty if there are no "proc" entries in the snmpd.conf file
+
+
+#
+#  Disk Monitoring
+#
+                               # 10MBs required on root disk, 5% free on /var, 10% free on all other disks
+disk       /     10000
+disk       /var  5%
+includeAllDisks  10%
+
+#  Walk the UCD-SNMP-MIB::dskTable to see the resulting output
+#  Note that this table will be empty if there are no "disk" entries in the snmpd.conf file
+
+
+#
+#  System Load
+#
+                               # Unacceptable 1-, 5-, and 15-minute load averages
+load   12 10 5
+
+#  Walk the UCD-SNMP-MIB::laTable to see the resulting output
+#  Note that this table *will* be populated, even without a "load" entry in the snmpd.conf file
+
+
+
+###############################################################################
+#
+#  ACTIVE MONITORING
+#
+
+                                    #   send SNMPv1  traps
+ trapsink     localhost public
+                                    #   send SNMPv2c traps
+#trap2sink    localhost public
+                                    #   send SNMPv2c INFORMs
+#informsink   localhost public
+
+#  Note that you typically only want *one* of these three lines
+#  Uncommenting two (or all three) will result in multiple copies of each notification.
+
+
+#
+#  Event MIB - automatically generate alerts
+#
+                                   # Remember to activate the 'createUser' lines above
+iquerySecName   internalUser       
+rouser          internalUser
+                                   # generate traps on UCD error conditions
+defaultMonitors          yes
+                                   # generate traps on linkUp/Down
+linkUpDownNotifications  yes
+
+
+
+###############################################################################
+#
+#  EXTENDING THE AGENT
+#
+
+#
+#  Arbitrary extension commands
+#
+ extend    test1   /bin/echo  Hello, world!
+ extend-sh test2   echo Hello, world! ; echo Hi there ; exit 35
+#extend-sh test3   /bin/sh /tmp/shtest
+
+#  Note that this last entry requires the script '/tmp/shtest' to be created first,
+#    containing the same three shell commands, before the line is uncommented
+
+#  Walk the NET-SNMP-EXTEND-MIB tables (nsExtendConfigTable, nsExtendOutput1Table
+#     and nsExtendOutput2Table) to see the resulting output
+
+#  Note that the "extend" directive supercedes the previous "exec" and "sh" directives
+#  However, walking the UCD-SNMP-MIB::extTable should still returns the same output,
+#     as well as the fuller results in the above tables.
+
+
+#
+#  "Pass-through" MIB extension command
+#
+#pass .1.3.6.1.4.1.8072.2.255  /bin/sh       PREFIX/local/passtest
+#pass .1.3.6.1.4.1.8072.2.255  /usr/bin/perl PREFIX/local/passtest.pl
+
+# Note that this requires one of the two 'passtest' scripts to be installed first,
+#    before the appropriate line is uncommented.
+# These scripts can be found in the 'local' directory of the source distribution,
+#     and are not installed automatically.
+
+#  Walk the NET-SNMP-PASS-MIB::netSnmpPassExamples subtree to see the resulting output
+
+
+#
+#  AgentX Sub-agents
+#
+                                           #  Run as an AgentX master agent
+ master          agentx
+                                           #  Listen for network connections (from localhost)
+                                           #    rather than the default named socket /var/agentx/master
+#agentXSocket    tcp:localhost:705

roles/snmp-cs/handlers/main.yml

@@ -0,0 +1,3 @@
+---
+  - name: restart snmpd
+    service: name=snmpd state=restarted

roles/snmp-cs/tasks/main.yml

@@ -0,0 +1,14 @@
+---
+
+- name: Installation snmpd
+  apt:  name=snmpd state=present
+
+- name: Installation snmp
+  apt:  name=snmp state=present
+
+- name: Copie du fichier snmpd.conf
+  copy: src=snmpd.conf dest=/etc/snmp/
+  notify:
+    - restart snmpd
+  
+